7/10/2023 0 Comments Nordvpn linux![]() You’ve got working machines, as I understand it, using different Linux distros. I think the fact that your route doesn’t change (the results of the ip ro command above) is the key. + oifname "enp34s0" counter packets 2 bytes 232 drop + oifname "enp34s0" ct mark 0xe1f1 counter packets 0 bytes 0 accept + oifname "enp34s0" mark 0xe1f1 counter packets 0 bytes 0 ct mark set mark + iifname "enp34s0" counter packets 0 bytes 0 drop + iifname "enp34s0" ct mark 0xe1f1 counter packets 0 bytes 0 accept + oifname "enp34s0" counter packets 36 bytes 2814 drop + oifname "enp34s0" ct mark 0xe1f1 counter packets 831 bytes 130084 accept + oifname "enp34s0" mark 0xe1f1 counter packets 831 bytes 130084 ct mark set mark + oifname "enp34s0" ip daddr 103.86.96.100 counter packets 0 bytes 0 accept + oifname "enp34s0" ip daddr 103.86.99.100 counter packets 0 bytes 0 accept Type filter hook output priority filter policy accept + iifname "enp34s0" counter packets 18 bytes 2562 drop + iifname "enp34s0" ct mark 0xe1f1 counter packets 1 bytes 120 accept + iifname "enp34s0" ip saddr 103.86.96.100 counter packets 0 bytes 0 accept + iifname "enp34s0" ip saddr 103.86.99.100 counter packets 0 bytes 0 accept Type filter hook input priority filter policy accept I didn’t show the entire output of the ¨nft list ruleset¨ command, but only the differences. Then I will paste the text of differences.txt here. I would look at routes and ruleset both before and after starting the gizmo: ip ro I don’t know Nordvpn, but if it does tamper with firewall too … I have seen setups where that (or equivalent) was not sufficient the initial local config had quirks that the VPN client failed to anticipate. That extra static route keeps the whole up. Therefore, the machine must continue to send the packets of the VPN connection via “local internet”.Īt least one OpenVPN setup did actually create following routes: default via (GW2 in VPN) If it puts anything out from vp0, it will get those packets, encrypt them, and should send a packet to VPN server. Now the question is: How does the VPN client continue to send packets to the VPN server?Īccording to routing table it should send to GW2 by tossing packets out from vp0. Link-local subnet (VPN): use interface (vp0) However, without the “split tunnel” the default route is changed to be someone in the VPN subnet (once known as “roadwarrior” config): default via (GW2 in VPN) Fine, you have two sets of neighbours: link-local subnet (VPN): use interface (vp0) The VPN offers a new interface and subnet behind it. toss out from em1 (unless the VPN server is in the link-local subnet …) It must use the routes above:įorward to GW, i.e. Now your VPN client establishes connection to VPN server. Link-local subnet (LAN): use interface (em1) Wget https: ///deb/nordvpn/debian/pool/main/nordvpn-release_1.0.0_all.We do know that in default (one interface) setup the routing table looks like: default via (GW in LAN) If you only have access to a command like you can also do a: cd Downloads ![]() Go ahead and download the NordVPN Repository Package from here. ![]() Conclusion Step 1 – Downloading the NordVPN Repository Package. ![]() Step 2 – Installing the NordVPN Repository.Step 1 – Downloading the NordVPN Repository Package.Gladly, it’s really easy to install NordVPN on Linux and I am going to show you how to do it. Unfortunately, NordVPN doesn’t come with a nice GUI like PIA on Linux. Now, after using NordVPN for a good while, I had to install it on a couple of Linux machines and thought the process might not be as straightforward for everyone as it is for me. I recently wrote an article that compared the two most popular VPN providers out there: Private Internet Access and NordVPN.
0 Comments
Leave a Reply. |